Pneumatic Toe Pincher Coffin, Part 2

On to the pneumatics. First I needed to find a quiet (and affordable) compressor to hide in the garage that won't make a racket. I settled on the GMC Syclone 6310.

I decided the best place for the pneumatic cylinder was at the foot so that it is not easily seen. The 72.5" long coffin will still have some room at the foot even after the 5'6" skeleton is placed inside.

I want the coffin to open automatically when someone approaches. I figured the easiest way to do this was to use a cheap Motion-Sensing Flood Security Light- without any light bulbs installed. Instead, a light socket outlet would be screwed into one of the sockets and an ungrounded extension cord run to the coffin. To keep things simple, as many of the components in the coffin should use 120VAC directly.

Working from the size of the bottom panel, 11-3/4" x 11", I had to find a pneumatic cylinder that would fit in the foot of the coffin. McMaster-Carr has the best selection of pneumatic components. I purchased the following items:

Qty	MC Part #	Description	Each
1	6534K18	Quick Disconnect Hose Coupling 1/8" NPT female x 1/4" Industrial Plug	$1.84
1	5644K91	Assemble-Your-Own Retracting Air Hose, Red, 1/8" NPT, 25'	$12.68
6	5644K51	Easy To Install 1/8" NPT Male brass fittings	$4.11
1	4414K32	Air Filter	$7.38
1	6692K16	In Flow Control Valve, 1/8" NPTF to 1/8" NPTF	$20.22
1	7889K22	Directional Control 3-Port SS Solenoid Valve, 1/8 NPT Female, 200 PSI, 120 VAC	$113.86
1	6498K537	1-1/16" bore cylinder, 5" stroke, 1/8" NPT	$36.54
1	9066K12	Exhaust Flow Control Valve, Male Thread to Push-to-Connect Tube, 1/8" NPT For 1/4" OD	$23.27
1	8457T31	Push-to-Connect Muffler Plastic, 1/4" Stem OD, 52 SCFM	$7.38
1	6498K72	Pivot-mount cylinder bracket set	$3.05
1	6498K43	Rod clevis with pin	$3.88

I could not find any 1/8" NPT rubber flexible air hose and ended up ordering some rigid retracting air hose. McMaster-Carr sells this along with brass fittings as part of their "Build Your Own Air Hose" solution. I cut the rigid hose into shorter lengths and attached the fittings to make three separate hoses.

To make sure everything works correctly, I "breadboarded" the components on the workbench to test them out.

I recommend using pipe joint compound on the threaded connectors before screwing them into the components to prevent air leaks. A squirt bottle filled with soapy water can be used after the system is pressurized to locate leaks.

The 1/8" NPT to "Industrial" Quick-Disconnect adapter allowed me to use standard air hose QD connectors - treating the system like any other air powered tool for use with the compressor. Home Depot did not have any black air hose so I found one made by Goodyearhere in the U.S.A.

One end of the 50' black air hose connects to the compressor. I set the regulator to 90 PSI. The other end of the hose connects to the quick-disconnect connector which goes to the air filter. The air filter removes any dust or debris from the air supply so it does not get into the components. The filter connects to an inline flow control which allows you to adjust the rate at which the coffin door opens. The flow control connects to the normally closed port on the valve. The cylinder connects to the port that is switched between the normally closed and the normally open ports. A 90-degree flow control is screwed into the normally open port on the valve. This flow control allows you to adjust the rate at which the coffin door closes. An exhaust muffler is plugged into the flow control to keep the noise of escaping air to a minimum.

Since the stroke of the cylinder is 5", the rod end will need to be attached approximately 3.5" up the lid from the edge.
An X10 RC6500 Key Chain Remote Starter Kitallows manual override of the coffin while the motion sensor light is tripped. This particular unit retains its on/off state even when unplugged. Leaving the unit "on" lets the motion sensor control the coffin. Since the motion sensor may be tripped prematurely, or may stay on too long, the remote control provides a means to manually close and open the coffin if multiple groups of kids are walking past the motion sensor.

Continue to: Pneumatic Toe Pincher Coffin, Part 3

Pneumatic Toe Pincher Coffin, Part 1

This year's challenge was for me to learn a bit about pneumatics and try to build a coffin that would automatically open when kids walk past it. Spooky skeleton inside, maybe some cool lighting and sound effects.

After reading Animatronics: Guide to Holiday Displays, I felt ready to begin this project.

First, I needed a "toe pincher" coffin plan. I searched the internet and found a few designs but they did not look quite right. I knew I was going to place a 4th quality bucky skeleton in the coffin, and that skeleton is 5'6" tall. Adding 3" all around for "padding" I knew approximately what the size of the coffin needed to be. I decided to write a little trigonometry program to solve for a set of measurements where the side panels would require no more precision than .25 inches.

The program produced 10 designs which I drew up and compared. I selected one design as most visually appealing. Click the image below to view the final design.

While all the panels are of easy-to-cut dimensions, the angles are not so straightforward. I decided to make angle templates (download: 48, 54, 76) to help align the miter saw. UPDATE 10/11/2021 the angle template links should be working now.

The only other dimension I needed to determine was the height, or depth of the coffin. That is, if the coffin is laying flat on the ground, how high it comes up from the ground. I decided on 11 inches.

Cutting and assembling the coffin is a 1-2 day project. The panels, base and lid are 1/2" birch plywood. I decided to use small 2" hinges with removable pins to connect all the panels together and to the base. That way I can take the pins out and break the coffin down into pieces for storage if space is tight.

After attaching the frame to the base and adding the lid, I painted the entire coffin black, inside and out. I then started to wipe down the sides with green fluorescent paint mixed with water. It is my hope that this will give the coffin a spooky antiqued look when lit with a blacklight.

Continue to: Pneumatic Toe Pincher Coffin, Part 2

Monster Mud

I've been hearing about a concoction made from 5 parts drywall mud and 1 part latex paint called Monster Mud that can be used to dress up Halloween props.

Bloodsworth Manor has a cool coffin covered with the stuff.

Speaking of coffins, I need to get cracking on learning pneumatics and try to build an automatic open/close coffin before October...

Gameboard Prototype

Leaving a Dwarven Forge dungeon layout on the dining table between sessions is not ideal, and who wants to break it down and set it back up?

So I sketched out plans for a game board that will sit in the middle of my dining table, allowing 13" of usable depth to the edge for players to put their character sheets and stuff.  I'll route the edges with a cove bit so that it will be easier to pick up off the table with my fingers.  The top will be covered with a grass mat and the bottom will be lined with felt to protect the table.

I'll draw a grid spaced at one-inch intervals so that the gameboard can also be used as a battlemat.

1. Since this is a prototype the first time around I used a 2' x 4' x 5/8" sheet of birch plywood from Home Depot.  These are precut and ready to go.
2. Measure in 12" from one end and each side to find where to drill a 1/8" hole for the Jasper circle cutting guide pin to go. NOTE: Cheat this in a little more away from the edge to make sure you don't get a small flat spot at the tip of the circle.
3. Use a Whiteside RU5125 spiral cutting bit in the router and make several passes no deeper than 1/4" using the circle guide.  NOTE:  Attaching a vacuum to the router is important.  It produces a LOT of sawdust.
4. Repeat steps 2-3 for the opposite end of the sheet



5. Remove the Whiteside RU5125 bit and install the Whiteside 1804 cove bit.  Route the edge of the board all the way around.



6. Sand the edges
7. Apply wood stain to the edge with some overlap onto the faces of the board. After a day I added a coat of paste wax.



8. Apply the felt lining to the bottom using a spray adhesive.  Cut the excess using a hobby knife



9. Coat the top with shellac to seal the wood pores before using any adhesive. This ensures the mat does not develop air bubbles.
   
10. Apply the grass mat to the top using a spray adhesive.  Cut the excess using a hobby knife





11. Mark points for 1" gridlines using a green permanent marker, or whatever color you feel is least obtrusive yet still visible during a game.


12. Draw the gridlines with a ruler using the permanent marker

An ultra fine point green sharpie seems to turn out just right - the gridlines are visible but not too strong. Let the battle begin!
I'll be doing some research on reasonably-priced hardwood boards to make more of these out of rather than plywood.